HTH FILTERWASH
Liquid
3 L
CLEANS YOUR POOL FILTER
Effective on sand, diatomaceous earth and cartridge filters, this innovative product offers a powerful solution for removing impurities and extending the life of your filters.
By incorporating HTH FILTERWASH into your pool’s regular maintenance routine, you can ensure optimum water filtration, while reducing the need for additional chemical products.
ALSO CLEANS SALT CHLORINATOR CELLS
Characteristics
- High level of active ingredients
- Excellent detergent power
- Very effective against scale deposits
- Tinted liquid for easy rinsing
- Also available in 1 L bottle
Practical:
Graduated container
Tinted liquid for easy rinsing
Dosage
SAND FILTER
↳ 1 L to 2 L for filters with a diameter of less than 50 cm
↳ 2 L to 5 L for filters with a diameter of between 50 cm and 1 m
DIATOMITE FILTER OR CARTRIDGE FILTER
↳ Dilute the product at a rate of 1 L in 10 L of water
SALT ELECTROLYZER CELL
↳ Dilute the product at a rate of 1 L in 4 L of water
- SAND FILTER :
- Step 1: Open the filter.
- Step 2: Drain the filter down to the sand level.
- Step 3: Pour the product into the filter:
- 1 to 2 L of product for a filter with diameter below 50 cm.
- 2 to 5 L for a filter with diameter between 50 cm and 1 m.
- 5 to 20 L for a filter with diameter between 1 m and 1.5 m.
- Step 4: Leave to work for 12-24 hours.
- Step 5: Backwash the filter until all colour has disappeared from the site glass (where available).
- Step 6:Rinse the filter.
- DIATOMITE FILTER OR CARTRIDGE FILTER:
- Dilute product to a ratio of 1 litre for 10 litres of water in a container.
- Immerse items to be cleaned into container holding the solution.
- Leave to stand for at least 2 hours.
- Brush then rinse the items.
- SALT ELECTROLYSIS:
- Dilute the product at the rate of 1 liter in 4 liters of water.
- Soak the scaled electrodes in the solution thus prepared until the scale has completely disappeared (count 2 to 3 hours).
- Rinse the electrodes with plenty of water until the foam disappears.
N° UFI
UFI:FA03-A0T0-C009-6KPJ
Certification
Danger
H290:May be corrosive to metals. H290:May be corrosive to metals. H314:Causes severe skin burns and eye damage. H314:Causes severe skin burns and eye damage. H335:May cause respiratory irritation. H335:May cause respiratory irritation.
P101:If medical advice is needed, have product container or label at hand. P102:Keep out of reach of children. P103:Read carefully and follow all instructions. P271:Use only outdoors or in a well-ventilated area. P280:Wear protective gloves/ protective clothing/ eye protection/ face protection. P301 + P330 + P331:IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. P303 + P361 + P353:W PRZYPADKU KONTAKTU ZE SKÓRĄ (lub z włosami): Natychmiast zdjąć całą zanieczyszczoną odzież. Spłukać skórę pod strumieniem wody lub prysznicem. P304 + P340 + P310:W PRZYPADKU DOSTANIA SIĘ DO DRÓG ODDECHOWYCH: wyprowadzić lub wynieść poszkodowanego na świeże powietrze i zapewnić mu warunki do swobodnego oddychania. Natychmiast skontaktować się z OŚRODKIEM ZATRUĆ/ lekarzem. P305 + P351 + P338 + P310:W PRZYPADKU DOSTANIA SIĘ DO OCZU: Ostrożnie płukać wodą przez kilka minut. Wyjąć soczewki kontaktowe, jeżeli są i można je łatwo usunąć. Nadal płukać. Natychmiast skontaktować się z OŚRODKIEM ZATRUĆ/ lekarzem. P405:Store locked up. P501:Dispose of contents/ container to an approved waste disposal plant.
Caution!
Keep this product in a dry, well ventilated place, at an average daily temperature not exceeding 35°C.
Never pour water onto this product as it may react violently if it enters into contact with small volumes of water.
The expiry date and the batch number appear on the packaging.
DO NOT MIX WITH ANY OTHER PRODUCTS. IF THE PRODUCT HAS TO BE DILUTED, FOLLOW THE RECOMMENDED PROCEDURE.
Ingredients contributing to the classification of the product
hydrochloric acid ; C10-guerbet alcohol ethoxylate (>5-10EO) ; phosphoric acid ;
Biocidal product:
less than 5 % Non-ionic surfactants
